Netopia has just introduced a new line of Wireless Gateways utilizing 802.11x technology for complete interoperability and Wi-Fi compliance. Netopia 3-D Reach is superior to today's conventional wireless implementations by incorporating a wireless subsystem specifically designed for enhanced wireless range, coverage and performance.
PLEASE NOTE: The purpose of this Quick Guide is to outline basic configuration of the wireless LAN networking properties of the Netopia 3300 Series Residential Wireless Gateway. It should be noted that additional configuration can enhance the level of network security available above that outlined in this Quick Guide.
Click Here! if you'd like to use MAC Authentication for additional network security.
Click Here! if you'd like to use WEP Encryption for additional network security. WEP can be used alone or in conjunction with MAC Authentication.
This document assumes a properly working DSL internet connection.
Below is a list of hardware and firmware loads that this Technical Note is based upon:
| Hardware | Type | Firmware/Version |
| Netopia 3347W | ADSL Gateway | 7.2 R1 and later |
Click Here! if you have the 3347W/3387W Enterprise Series router.
- For the initial wireless configuration, make certain your computer is connected directly to the router's 10/100 BaseT Ethernet port.
- Out of the box, the Netopia router is a DHCP server. Make sure the computer's TCP/IP properties are set to obtain an IP address automatically from the router.
- Be sure to remove any Gateway IP's you have installed and disable DNS.
- Once you have obtained an IP address from the Netopia, you are ready to browse into the router.
PLEASE NOTE: The IP Addressing in this document is for illustrative purposes only. The public IP's provided by your ISP will be different and unique to your internet account. With Network Address Translation enabled, any private network addressing scheme can be used that is consistent with your LAN settings.
- Browse into the Netopia router's web interface at 192.168.1.254. (if unchanged from factory def.)
- If you did not obtain an address from the router dynamically, assign the workstation an address of 192.168.1.[x], [x] being any number between 1 and 253, and a subnet mask of 255.255.255.0. The gateway IP is 192.168.1.254, the default IP address of the Netopia LAN interface.
- Login using admin as the username and the admin level password. The factory default setting for the password is the router serial number. You should change this for better security. Only the administrator can save changes to the database.
- Verify you are in Expert Mode.
- Click on Configure.
- Click on LAN.
- Click on Wireless in the Other LAN Options box.
- Check the Enable Wireless checkbox.
- You can use the default SSID (Network ID) setting, or change to your own setting. This must match the Network ID of the Wireless Network cards installed in the computer(s).
- Use Encryption: should be set to Off - No Privacy.
- Click on Submit.
- Click on Advanced under Other Wireless Options.
- The Default Channel setting is preset at 6. This refers to radio frequency ranges within the 2.4 Ghz range and can be changed as long as the wireless network settings match.
- Enable Closed System Mode: is Unchecked by default.
- When unchecked, or in Open Mode, this SSID will be broadcast as an available wireless network to any compatible WiFi Device within broadcast reach.
- When checked (enabled), or in Closed Mode, it will be necessary to enter the SSID value into the client card configuration to permit access to the available network.
- In Closed Mode the Netopia wireless network is hidden from the scanning features of other wireless-enabled computers. The only clients allowed to access your network are those configured with the same SSID value.
- Closed System mode is recommended for increased security from unauthorized access or unwanted detection of a wireless "hotspot".
- Enable WEP Encryption is Off - No Privacy.
- Click on Submit.
- Click on MAC Authorization.
- Enable Wireless MAC Auth should be Unchecked.
- Submit.
- Once you have input all necessary information, click on the
symbol in your upper right hand corner to validate the changes. - Validation passed, then click on Save and Restart.
Your Netopia router is now configured for both a wired and wireless LAN environment. The 10/100 Ethernet switch incorporated into the 3300 Wireless series router allows instant connectivity to your existing ethernet LAN, either directly plugged into the router's hub or to an external hub. The 3D Reach Wireless LAN will provide network access to 802.11b compliant devices on your network as well. Please consult the documentation provided with the wireless LAN card for individual manufacturers instructions and requirements.